SanDisk SDSDB-016G-A11 Product Manual Download Page 120 | Manualshive

Page: 120 / 123

background image

Host Design Considerations:

Application Note

NAND MMC and SD-based Products

Revision 1.0

© 2002 SanDisk Corporation

4

9/30/02, Lit# 80-11-00160

The maximum read and write time-out values for the MultiMediaCard and SD Card are
shown in Table 1.

Table 1.

MultiMediaCard and SD Card Maximum Read/Write Time-out Values

Product Time-out

Values

MultiMediaCard Typical

Maximum

Read

(TAAC + NSAC)

10 * (TAAC + NSAC)

Write

(TAAC + NSAC) * R2W_FACTOR

(TAAC) + NSAC) * R2W_FACTOR * 10

SD Card

Read

(TAAC + NSAC)

100ms

Write

(TAAC + NSAC) * R2W_FACTOR

250 ms

The factors used in calculating the values in Table 1—TAAC, NSAC, and
R2W_FACTOR—can be read directly from the CSD register of the MultiMediaCard and
SD Card.

The TAAC factor’s unit is time, and the NSAC factor has units of 100 clocks. You can
convert TAAC units to clock cycles by multiplying by the frequency of the clock and
calculate the time-outs in units of clock cycles if desired. Alternatively, given the
frequency of the clock, you can convert the NSAC units to time and calculate the time-
outs in units of time.

The R2W_FACTOR is a read-to-write factor and has no units. A design engineer can use
the time-out values derived from the CSD register to make the design compatible with all
MultiMediaCards and SD cards regardless of customer brand.

Interface

The MultiMediaCard and SD Card support multiple busses. Both cards support the 1-bit
SPI bus that includes bus pins DATin, DATout, CLK, and CS. The SPI bus is generally
found on Motorola and other major MCU manufacturer products.

The SD Card also supports a 4-bit and a 1-bit SD bi-directional bus mode. SD bus pins
are CLK, CMD, and DAT in 1-bit mode and CLK, CMD, and DAT[0:3] in 4-bit mode.

The MultiMediaCard also supports the 1-bit bi-directional MMC bus mode that has CLK,
CMD, and DAT bus pins. The CMD and DAT pins are bi-directional on the SD 1-bit, SD
4-bit, and MMC 1-bit.

The maximum burst rate achievable with the SD Card and MultiMediaCard depends on
the clock speed and bus mode. The burst rate is the data transfer rate between the card’s
buffer and host.

«
...
118
119
120
121
122
...
»

Summary of Contents for SDSDB-016G-A11




























































































































Reviews:

No comments

Related manuals for SDSDB-016G-A11

Brand: X-METAL Pages: 36

Brand: LaCie Pages: 22

Brand: ABSCO SHEDS Pages: 18

SmartStore SM2015

Brand: Riverlea Pages: 16

Brand: Kikusui Pages: 6

Brand: Holzmann Pages: 20

CANOPIA RUBICON

Brand: Palram Pages: 71

TotalStorage NAS 100

Brand: IBM Pages: 18

Brand: I-O DATA Pages: 2

Brand: Maxtor Pages: 63

SIMODRIVE 611-D

Brand: Siemens Pages: 189

Brand: Siemens Pages: 301

Brand: Gateway Pages: 58

SOHORAID SR8-TB3

Brand: Stardom Pages: 29

GlobeTrotter GT MAX "7.2 READY"

Brand: Option Wireless Technology Pages: 12

Brand: Clarke Pages: 8

PREMIER 15151GK

Brand: ABSCO SHEDS Pages: 21

Premier 23231GK

Brand: ABSCO SHEDS Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands