background image

ATA Command Description 

SanDisk CompactFlash Card OEM Product Manual 

If the Sector Count Register contains a valid value and the block count is supported, the value 
is loaded for all subsequent Read Multiple and Write Multiple commands and execution of 
those commands is enabled. If a block count is not supported, an Aborted Command error is 
posted, and Read Multiple and Write Multiple commands are disabled. If the Sector Count 
Register contains 0 when the command is issued, Read and Write Multiple commands are 
disabled. At power on, or after a hardware or (unless disabled by a Set Feature command) 
software reset, the default mode is Read and Write Multiple disabled. 

Table 5-28

 Set Multiple Mode 

Bit 

Command (7) 

C6H 

C/D/H (6) 

X

 Drive

 

X

 

Cyl High (5) 

Cyl Low (4) 

Sec Num (3) 

Sec Cnt (2) 

Sector Count 

Feature (1) 

5.1.20 

Set Sleep Mode–99H, E6H 

This command causes the card to set BSY, enter the Sleep mode, clear BSY and generate an 
interrupt. Recovery from sleep mode is accomplished by simply issuing another command (a 
reset is permitted but not required). Sleep mode is also entered when internal timers expire so 
the host does not need to issue this command except when it wishes to enter Sleep mode 
immediately. The default value for the read to sleep timer is 5 milliseconds. This time base (5 
msec) is different from the ATA Specification. 

Table 5-29

 Set Multiple Mode 

Bit 

Command (7) 

99H or E6H 

C/D/H (6) 

X

 Drive

 

X

 

Cyl High (5) 

Cyl Low (4) 

Sec Num (3) 

Sec Cnt (2) 

Feature (1) 

02/07, Rev. 12.0 

5-22 

© 2007 SanDisk Corporation 

Summary of Contents for CompactFlash Extreme III













































































































Reviews: