background image

S&C Instruction Sheet 761-515   

3

Introduction

Warranty

The warranty and/or obligations described in S&C’s standard conditions of sale, as set 
forth in Price Sheet 150, plus any special warranty provisions, as set forth in the applicable 
product-line specification bulletin, are exclusive. The remedies provided in the former 
for breach of these warranties shall constitute the immediate purchaser’s or end user’s 
exclusive remedy and a fulfillment of all seller’s liability.  In no event shall seller’s liability 
to the immediate purchaser or end user exceed the price of the specific product that gives 
rise to the immediate purchaser’s or end user’s claim.  All other warranties, whether express 
or implied or arising by operation of law, course of dealing, usage of trade or otherwise, 
are excluded.  The only warranties are those stated in Price Sheet 150, and THERE ARE 
NO EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE. ANY EXPRESS WARRANTY OR OTHER OBLIGATION 
PROVIDED IN PRICE SHEET 150 IS GRANTED ONLY TO THE IMMEDIATE PURCHASER 
AND END USER, AS DEFINED THEREIN. OTHER THAN AN END USER, NO REMOTE 
PURCHASER MAY RELY ON ANY AFFIRMATION OF FACT OR PROMISE THAT RELATES 
TO THE GOODS DESCRIBED HEREIN, ANY DESCRIPTION THAT RELATES TO THE 
GOODS, OR ANY REMEDIAL PROMISE INCLUDED IN PRICE SHEET 150.

Warranty 

Qualifications

The standard warranty is applicable to the S&C Alduti-Rupter Switch detailed in this 
instruction sheet except when it is power operated using a switch operator of other than 
S&C manufacture.

Summary of Contents for Alduti-Rupter





























Reviews: