Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
T h e
i s a G i g a b i t u n m a n a g e d E t h e r n e t s w i t c h w i t h
I G S - 1 0 8 2 G P
8x10/100/1000Base-T(X) ports and 2x100/1000Base-X SFP ports, ideal for
applications that demand high bandwidth. The device support a wide range
power input between 12~48VDC to satisfy the demands of devices.
Configuration of SFP speed is made easy with a 4-pin DIP switch which can
also be set to send power failure alerts. With a wide operating temperature
range from -40 C to 75 C and dual power inputs, the devices can work
o
o
perfectly in harsh environments.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised
Mounting of the equipment in the rack should be
Mechanical Loading:
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
Safety & Warnings
Dimension
Panel Layouts
1. Power status LED
2. Fault LED
3. LNK/ACT LED for SFP modules
4. SFP Ports
5. Gigabit LAN ports
6. Link/Act LED for Gigabit LAN
ports
7. Speed LED for Gigabit LAN ports
Package Contents
Contents
DIN-rail Kit
IGS-9042GP
Pictures
Number
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
QIG
X 1
X 1
Wall-mount Kit
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
1. Terminal blocks: PWR1, PWR2
, Relay
2. DIP switch
1
Installation
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Screw the wall-mount kit onto the rear panel of the switch. A total of six
screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3:
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
Q I G
IGS-1082GP
1907-2-29-IGS1082GP-1.0
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches,
routers,
or
hubs).
Please
refer
to
the
following
table
for
cable
specifications.
54.3
4
5
.0
14.0
40.0
5
0
.0
2
5
.3
1
1
6
.0
18.0 18.15
51.0
2
0
9
.3
7
.3
5
1
8
7
.4
R2.5
R3.95
4
6
.0
2
1
IGS-1082GP
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Unmanaged Gigabit Switch
32.2
3
3
.6
1
2
.5
54.3
1
4
5
.1
108.5
19.0
32.2
G8
G10
G6
G10
G9
100/1000X
PWR
PWR1
PWR2
Fault
LNK/ACK
IGS-1082GP
G6
G4
G2
G7
G5
G3
G1
10/100/1000T
Speed
G8
G10
G6
G10
G9
100/1000X
PWR
PWR1
PWR2
Fault
LNK/ACK
IGS-1082GP
G6
G4
G2
G7
G5
G3
G1
10/100/1000T
Speed
4
3
6
5
7
2
G8
G10
G6
G10
G9
100/1000X
PWR
PWR1
PWR2
Fault
LNK/ACK
IGS-1082GP
G6
G4
G2
G7
G5
G3
G1
10/100/1000T
Speed
Dip Switch
DIP-Switch 1
Power-2 failed warning : (ON) enable, (OFF) disable
DIP-Switch 2
Power-1 failed warning : (ON) enable, (OFF) disable
DIP-Switch 3
DIP switch 3 and 4 (ON) : SFP speed setting to 100Mbps
DIP-Switch 4
DIP switch 3 and 4 (OFF) : SFP speed setting to 1000Mbps(default)
