Samsung WM1245A Service Manual Download Page 27

Page: 27 / 76

- 24 -

1. Troubleshooting (Test Mode)

①

. Connect the power cord to the power socket.

②

. Switch the Power Button on while pressing the Spin and Drying Selector buttons.

③

. All of the LEDs will be turned on in the Display window. (Check the LEDs.)

If you release the button being pressed,

will be displayed. (Initial condition of Test Mode)

SW No.

Load

LED Display

SW1

The sequential operation of the water supply
valves.

(Pre→Dry→Cold Water→Hot Water→Relay15→OFF)

A) Use the SW2 door lock before you can operate

the valve.

Pre

Dry

Cold

Hot

Relay15

Cold,

30℃

40℃

60℃

75℃

95℃

Check the silver nano kit

A) Check the kit for a silver nano model when it

uses the cold water valve

B) ㅂE error occurs for an unconnected silver kit

and high electrical current (only applicable to
test mode)

- The silver nano kit LED turns on: Check

the silver nano kit

- A/B Operation in turns The water Supply

LED turns on, Up/Down in turns.

- More than a low level of current flows:

The silver nano and Ag+ LEDs turn on

with a beep.

SW2

Door Lock Switch : Door Lock Test

A) When the door is open, a "dE" error with a

beep occurs. When closed, auto lock is performed

-. When the door is closed, the door

lock LED turns on.

SW3

-. Door Lock Switch: Door Unlock Test

A) When the door is unlocked, each load

check turns off.

B) Performs unlock regardless of the

conditions.

-. The door lock LED turns off when

the door lock is set off.

4-2. Troubleshooting (Test Mode)

sw1

sw2

sw3

sw4

sw5

sw6

Summary of Contents for WM1245A













































































Search results

Summary of Contents for WM1245A

Reviews:

Related manuals for WM1245A

Brands by name

Popular brands

Samsung WM1245A, Service Manual

Search results

Summary of Contents for WM1245A

Reviews:

Related manuals for WM1245A

Brands by name

Popular brands