Samsung WM1245A Service Manual Download Page 7

Page: 7 / 76

- 4 -

■

Installation Manner

1. Select an installation place in

advance.

▶

The distance between the washing
machine and the wall must be at
least 10cm.

2. Check the balance

▶

If you press down or shake any part of
the front, left or right side of the washing
machine and it still wobbles, adjust the
feet again until the machine is standing
solidly.

3. Adjust the height using the adjustable feet.

▶

The machine is in a

balanced state when all

four adjustable feet are

firnly on the ground and

there is no movement.

If uneven

▶

Adjust the lowest of the 4 adjustable feet while lifting the washing machine a little.

▶

Adjust the height by turning the nut to the left as in the figure.
(The adjustable foot will be lengthened.)

※

Caution

※

After adjusting the horizontal
balance, fix the nut tightly so
that it doesn't come loose
through vibration or noise.

▶

Tighten the nut after making
the adjustments.

Summary of Contents for WM1245A













































































Search results

Summary of Contents for WM1245A

Reviews:

Related manuals for WM1245A

Brands by name

Popular brands

Samsung WM1245A, Service Manual

Search results

Summary of Contents for WM1245A

Reviews:

Related manuals for WM1245A

Brands by name

Popular brands