Samsung WF220ANW/XAA Training Manual Download Page 36

Page: 36 / 93

4. Test Mode & Error Check

Continuous Run Mode:

1. Press Delay Start + Extra Rinse Key for 7 sec during Power On State (Normal User Mode) .

2. Once in Continuous Run Mode, The seven segments will no longer display “0000” and will alternate

between displaying the number of cycles of the completed course and the remaining time of the course.

3. The Continuous Run Mode will repeat the previous cycle until continuous run mode is cancelled.

4. During Continuous Run Mode, press Delay Start + Extra Rinse Key for 7 sec to return to normal user mode.

The seven segments will no longer display the number of cycles and will display the maintenance time
only.

5. If you exit Service Mode after entering it from Continuous Mode, the washing machine returns to

Continuous Mode.

6. If power is lost in Continuous Run Mode (that is, when the power plug is disconnected or the Power key is

pressed turning the washing machine off), the mode is released when the washing machine is turned on
again.

4-1-3. Continuous Run Mode

Summary of Contents for WF220ANW/XAA






























































































Search results

Summary of Contents for WF220ANW/XAA

Reviews:

Related manuals for WF220ANW/XAA

Brands by name

Popular brands

Samsung WF220ANW/XAA, Training Manual

Search results

Summary of Contents for WF220ANW/XAA

Reviews:

Related manuals for WF220ANW/XAA

Brands by name

Popular brands