Samsung WF220ANW/XAA Training Manual Download Page 40

Page: 40 / 93

4. Test Mode & Error Check

Quick Spin Test Mode:

As it enters into the Quick Spin Test Mode, it starts spinning and reaches to its maximum RPM.

Once the Spin speed reaches the maximum RPM, the speed drops immediately.

To hold Quick Spin Test Mode (entering Hold Speed Mode), press the Start/Pause button. If the Start/Pause

button is pressed during Quick Spin Test Mode, it will stop accelerating and hold its spinning speed for 10
minutes before going back to Quick Spin Test Mode.

Also, to cancel the hold and allow Quick Spin Test Mode to continue, press the Delay Start and Temp Keys

together for 3 seconds.

If you hold down the Delay Start and Temp. keys for three (3) seconds when the washing machine is not in Hold

Speed Mode, Quick Spin Mode is exited and Service Mode is restored.

4-1-5. Quick Spin Test Mode

Summary of Contents for WF220ANW/XAA






























































































Search results

Summary of Contents for WF220ANW/XAA

Reviews:

Related manuals for WF220ANW/XAA

Brands by name

Popular brands

Samsung WF220ANW/XAA, Training Manual

Search results

Summary of Contents for WF220ANW/XAA

Reviews:

Related manuals for WF220ANW/XAA

Brands by name

Popular brands