Samsung TS-451D2 User Manual Download

Page: 33 / 54

LED

Status

Description

LAN

Orange

The network connection is operating at 1 Gbps.

Flashes orange

The device is being accessed from the network.

Off

The device is not connected to a network.

1 Gigabit
Ethernet
speed

Green

The network connection is operating at 1 Gbps.

Orange

The network connection is operating at 100 Mbps.

Off

• The network connection is operating at 10 Mbps.

• There is no network connection.

1 Gigabit
Ethernet
activity

Orange

A network connection has been established.

Flashes orange

The device is being accessed from the network.

Off

There is no network connection.

USB

Blue

A USB device connected to the USB One Touch Copy port is
detected.

Off

No USB expansion unit has been detected.

Audio Alert

Duration

Frequency

Description

Short beep (0.5 seconds)

• The NAS is starting up.

• When the reset button is

pressed for 3 seconds, the
NAS resets configurations.

• When the reset button is

pressed for 10 seconds, the
NAS resets configurations and
reboots.

• The operating system was

updated.

• The device is starting USB

One-Touch Copy.

The USB device has been
removed (USB One Touch copy
button).

• Cannot detect installed disk.

• The NAS data cannot be

copied to the external storage
device connected to the front
USB port.

TS-451D2 User Guide

Basic Operations

Summary of Contents for TS-451D2























































Search results

Summary of Contents for TS-451D2

Reviews:

Related manuals for TS-451D2

Brands by name

Popular brands

Samsung TS-451D2, User Manual

Search results

Summary of Contents for TS-451D2

Reviews:

Related manuals for TS-451D2

Brands by name

Popular brands