Samsung TH026EAV Installation Manual Download Page 21

Page: 21 / 24

E-

ENGLISH

Troubleshooting (continued)

Display

Explanation

Indoor unit communication reception error

Communication error between the outdoor and indoor unit

Indoor unit temperature sensor (Short/Open)

Indoor unit Eva In sensor (Short/Open)

Indoor unit Eva Out sensor (Short/Open)

Indoor unit Eva In sensor secession

Indoor unit Eva Out sensor secession

Indoor Eva In and Out sensor secession error

Secondary(Electronic)heater sensor 1 error

Secondary(Electronic)heater sensor 2 error

Secondary(Electronic)heater sensor 3 error

Indoor unit float S/W 2nd detection

Indoor fan error

Mixed operation error

EEPROM error

EEPROM option setting error

Error regarding special sales taxes

Electronic heater discharge temperature protection error

Electronic heater windless error

Indoor unit number setting error(The outdoor unit informs the error)

Wired remote controller



If an error occurs, is displayed on the wired remote controller.

If you would like to see an error code, press the Test button.

Indoor unit

Summary of Contents for TH026EAV

























Search results

Summary of Contents for TH026EAV

Reviews:

Related manuals for TH026EAV

Brands by name

Popular brands

Samsung TH026EAV, Installation Manual

Search results

Summary of Contents for TH026EAV

Reviews:

Related manuals for TH026EAV

Brands by name

Popular brands