background image

COLOR CCD CAMERA

COLOR CCD CAMERA

User’s Manual

User’s Manual

5

4

Features

Warning

Wide Dynamic Range(WDR)

Fine Picture Condition Under Very
Low Illumination (SENSE UP)

1/3  high density CCD and digital
processor permit high quality pictures to
be captured in very low light condition.

SV-II DSP chip built-in 

SAMSUNG TECHWIN

allows the camera to find the best picture
conditions in any environment and
automatically gives a necessary light level
compensation, so you can always obtain
the clear picture, the finest detail and
perfect light contrast.

MOTION DETECTION

The camera transmits an alert signal to
the REMOTE jack when it detects motion
of an object. If you connect an optional
alarm to the camera, you can get the
effective surveillance.

Auto Iris Vari-Focal Lens Built In 

The focal length of lens is 3.8 to 9.5
mm, equivalent to 2.5x zoom.
The built-in lens allows the camera to
have a Wider Dynamic Range, therefore
you can use in various applications.

Wide Range ATW 

The White Balance can be automatically
adjusted in response to light condition
so that you can observe in an appropriate
color balance.

Adoptable

One power connection self-configures
to either 12V DC or 24V AC.
AC line lock standards with all cameras
in 24V AC operation.

High Resolution

The horizontal resolution of 500TV lines
can be achieved by using a high density
CCD having Double Speed 410,000 pixels
SONY CCD, which provides clean,
noiseless and reliable pictures.

The camera needs periodic inspection.

Contact an authorized technician for inspection.

Stop using your camera when you find a malfunction.

If you use your camera around smoke or unusual heat for a long time, a
fire may be caused.

Do not Install the camera on a surface that can not support it.

Unless the surface is suitable, it could cause falling or other hazards.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not disassemble the camera.

It may result in fire, electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in fire or other hazards.

SSNR(Samsung Super Noise
Reduction) CHIP

SOC-4120AN/P has an assistant DSP chip
that can remove image noise efficiently
and it shows clean and obvious image in
low luminance

Electronic DAY/NIGHT

In normal or high luminance, camera
maintains color mode. On the contrary, it
get changed into B/W mode in low
luminance. 

Summary of Contents for SOC-4120AN





















Reviews: