Samsung SL-C1860FW Page 107 Service Manual Download

Page: 107 / 136

4. Alignment and Troubleshooting

► Error Code

C2-2320

C2-2410

C2-3320

C2-3410

C2-4320

C2-4410

C2-5320

C2-5410

► Error message

Yellow Toner Failure: #C2-2320. Install yellow toner cartridge again.

Install yellow toner cartridge.

Magenta Toner Failure: #C2-3320. Install magenta toner cartridge again.

Install magenta toner cartridge.

Cyan Toner Failure: #C2-4320. Install cyan toner cartridge again.

Install cyan toner cartridge.

Black Toner Failure: #C2-5320. Install black toner cartridge again.

Install black toner cartridge.

► Symptom

The toner cartridge is not installed or the CRUM has some problem.

► Troubleshooting method

1) Check if the toner cartridge is installed properly. Turn the machine off then on.

2) If the error message is not disappear, remove the toner cartridge. Thoroughly roll the cartridge five or six times to

distribute the toner evenly inside the cartridge. And reinstall the toner cartridge.

3) If the problem persists, check that the CRUM contact area is contaminated. Clean it.

4) If the problem persists, replace the toner cartridge with new one.

4-37

Summary of Contents for SL-C1860FW







































































































































Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands

Samsung SL-C1860FW, Service Manual

Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands