Samsung SL-C1860FW Page 105 Service Manual Download

Page: 105 / 136

4. Alignment and Troubleshooting

► Error Code

A3–3311

A3–3312

► Error message

Actuator Sensor Failure #A3-3311: Call for service if the problem persists.

Actuator Sensor Failure #A3-3312: Call for service if the problem persists.

► Symptom

The outer temperature sensor is defective.

► Troubleshooting method

1) Turn the machine off then on. If the error persists, turn the machine off again.

2) Enter the tech mode. Check the temperature sensor output.

3) If the sensor is defective, replace it.

4) If the temperature sensor is OK, replace the main board.

► Error Code

A3–3320

► Error message

Not proper room temperature. Change room temperature.

► Symptom

The value of the outer temperature sensor is out of normal area.

► Troubleshooting method

1) Check if the machine is installed in the proper area.

2) If the temperature sensor is defective, replace it.

4-35

Summary of Contents for SL-C1860FW







































































































































Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands

Samsung SL-C1860FW, Service Manual

Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands