Samsung SL-C1860FW Page 104 Service Manual Download

Page: 104 / 136

4. Alignment and Troubleshooting

► Error Code

A2-1210

A2-2110

► Error message

Actuator Fan Failure : #A2-1210. Call for service if the problem persists.

Actuator Fan Failure : #A2-2110. Call for service if the problem persists.

► Symptom

The SMPS fan or Fuser fan does no operate normally.

► Troubleshooting method

1) Turn the machine off then on. If the error persists, turn the machine off again.

2) Remove the right cover.

3) Check if the connection between main board and the related fan is correct.

4) If the connection is OK, replace the defective fan.

► Error Code

A3–3211

A3–3212

► Error message

Actuator Sensor Failure #A3-3211: Call for service if the problem persists.

Actuator Sensor Failure #A3-3212: Call for service if the problem persists.

► Symptom

The inner temperature sensor is defective.

► Troubleshooting method

1) Turn the machine off then on. If the error persists, turn the machine off again.

2) Enter the tech mode. Check the temperature sensor output.

3) If the sensor is defective, replace it.

4) If the temperature sensor is OK, replace the main board.

4-34

Summary of Contents for SL-C1860FW







































































































































Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands

Samsung SL-C1860FW, Service Manual

Search results

Summary of Contents for SL-C1860FW

Reviews:

Related manuals for SL-C1860FW

Brands by name

Popular brands