Samsung SF-3100 User Manual Download Page 20

Page: 20 / 111

Setup

1-10

Recording
TAM

Message

(SF-3100T

only)

The TAM (Telephone Answering Machine) message is an
outgoing message (OGM) which plays whenever a call comes
in and the machine is in TAM Mode. For more information
about reception modes, see “Reception Modes” on page 3-6.

Press and hold OGM until you hear a beep.

The display starts counting the recording time.

Speak into the microphone when ‘RECORD’

appears in the display. Make sure that you are
within a 30cm range.
You can record a message which lasts up to 60
seconds.

•

You are advised to record a message of less than 15 sec-

onds in duration to prevent the incoming faxes from
malfunctioning due to a long message.

•

Press Stop or OGM if you want to stop recording

before the time is up.

•

After the message has been recorded, the machine

briefly displays the date and time when the message
was recorded. Then, it displays the elapsed time as the
message plays back automatically.

Now, you’re ready to use the TAM reception
mode. To learn more about the answering
machine, see “The Answering Machine” on
page 4-1.

1. Telephone Answering Machine

Summary of Contents for SF-3100
















































































































Search results

Summary of Contents for SF-3100

Reviews:

Related manuals for SF-3100

Brands by name

Popular brands

Samsung SF-3100, User Manual

Search results

Summary of Contents for SF-3100

Reviews:

Related manuals for SF-3100

Brands by name

Popular brands