manualshive.com logo in svg

Samsung S3P80C5, User Manual

Share
Download
Samsung S3P80C5 User Manual Download Page 73

CONTROL REGISTERS                           

 

S3P80C5/C80C5/C80C8

4-10

IMR

 

— Interrupt Mask Register

DDH

Set 1

Bit Identifier

.7

.6

.5

.4

.3

.2

.1

.0

RESET

RESET

  Value

x

x

x

x

x

x

x

x

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Addressing Mode

Register addressing mode only

.7

Interrupt Level 7 (IRQ7) Enable Bit; External Interrupts P0.7–P0.4

1

Enable (un-mask)

.6

Interrupt Level 6 (IRQ6) Enable Bit; External Interrupts P0.3–P0.0

0

Disable (mask)

1

Enable (un-mask)

.5

Not used for S3P80C5/C80C5/C80C8.

.4

Interrupt Level 4 (IRQ4) Enable Bit; Counter A Interrupt

0

Disable (mask)

1

Enable (un-mask)

.3–.2

Not used for S3P80C5/C80C5/C80C8.

.1

Interrupt Level 1 (IRQ1) Enable Bit; Timer 1 Match or Overflow

0

Disable (mask)

1

Enable (un-mask)

.0

Interrupt Level 0 (IRQ0) Enable Bit; Timer 0 Match or Overflow

0

Disable (mask)

1

Enable (un-mask)

NOTES:

1.

When an interrupt level is masked, any interrupt requests that may be issued are not recognized by the CPU.

2.

Interrupt levels IRQ2, IRQ3 and IRQ5 are not used in the S3P80C5/C80C5/C80C8 interrupt  structure.

Summary of Contents for S3P80C5








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands