manualshive.com logo in svg

Samsung NX58R4311SS, Service Manual

Share
Download
Samsung NX58R4311SS Service Manual Download Page 43

43

4. Troubleshooting

This document can not be used without Samsung’s authorization.

This document can not be used without Samsung’s authorization.

SYMPTOM

DIAGNOSIS

REMEDY

Oven not 

operating
(No power,

No display)

* 

Measure the input voltage at the 

plug. (120VAC)

* 

Measure the input voltage at terminal 

T01 on the PCB .

* 

Check the circuit breaker or fuse for the 

range circuit.

* 

Make sure all wires are connected to the 

PCB.

* 

Measure the voltage at the 

CN01 connector on the PCB. 

(L1~N:120VAC)

* 

Repair or replace the loose or disconnected 

harness.

* 

Make sure that the bake, broil, and 

source control relays on the PCB are 

working normally.

* 

Make sure the harness connections 

at the PCB terminals (T02, T03) have 

not come loose or disconnected. 

* 

Replace the PCB if a relay has been 

damaged; relay is not working properly; or if 

the PCB have a crack in it. 

* 

Tighten or reconnect the PCB harness 

connections.

* 

After confirming the harness has been 

connected properly to the PCB, take the 

following action:

      - 

Repair of replace the harness.

      - 

Replace the PCB.

* 

Measure the resistance between 

both ends of the oven temperature 

sensor. (normal : 0 ohms)

* 

Make sure the harness connections 

at the PCB connector CN04 has not 

come loose or disconnected.

* 

Replace the oven temperature sensor.

* 

Repair or replace the harness.

* 

If problem still exists after confirming the 

oven temperature sensor and harness are 

working and connected properly, replace the 

PCB.

Oven  temperature  

rises too slowly.

* 

“E-08” will show on the display if 

the oven fails to reach 125˚F(52˚C) 

within 10 minute in a room 

temperature condition.

* 

Measure the oven temperature sensor 

resistance: (1080Ω at the room 

temperature). Replace a faulty oven 

temperature sensor. 

* 

Make sure the harness connections 

at the PCB terminals (T02, T03) have 

not come loose or disconnected.

* 

Repair or replace the harness.

* 

Make sure the broil and bake burners 

have been adjusted properly.

* 

Make sure the oven burner orifices 

are sized properly for the type of gas 

being used.

* 

Open or close the air shutter at the base of 

the burners to optimize the flame pattern.

* 

Replace with properly sized orifices:

Burner NG

LP

Orifice

mm

mm

Broil

1.64

1.02

Bake

1.90

1.15

       NOTE: 

High-altitude orifice kits are available.

* 

Make sure that the bake, broil, and 

source control relays on the PCB are 

working normally.

* 

Repair or replace the faulty relay.

* 

Make sure all harness connections are 

properly connected.

* 

Replace the PCB. 

Summary of Contents for NX58R4311SS




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands