Samsung NX58R4311SS Service Manual Download Page 40

Page: 40 / 67

4. Troubleshooting

This document can not be used without Samsung’s authorization.

4-1 Failure Display Codes

Failure code

CAUSE

SOLUTION

E-0E

Door locking error

(Door lock in wrong position after

1minutes.)

Disconnect electrical power to the range.

Remove the rear cover panel. Make sure the

wiring harness is properly connected to the

motorized door lock assembly.

Check motorized door lock assembly for

proper operating resistance.

With operating door lockout, measure a

voltage of connector on harness which is

linked with door lock motor.

(Normal

:Voltage : AC 120V)

Check the door locking switch to make sure

it is working properly.

* Replace PCB.

* Solder again if pattern is damaged or

parts is Wrong Contacted.

E-0E

* Replace faulty door lock switch or Lock motor.

*Disconnect power.

*Get rid of harness connected with Lock motor.

* Check the door lock switches(com-NO)

* Measure resistance of Lock motor

Coil.(1750~1850Ω at the room temperature)

*Check whether voltage(AC 120V) is offered

to lock motor with letting lock work or not.

*Check whether harness connected

normally into CN501 on PCB.

* Repair damaged harness or Replace.

*Measure resistance CN501 on PCB.

(COM-NO: ∞ at the room temperature)

*COM : Yellow Wire *NO : White Wire

END

Door lock

Switch

COM

CN501

Summary of Contents for NX58R4311SS




































































Search results

Summary of Contents for NX58R4311SS

Reviews:

Brands by name

Popular brands

Samsung NX58R4311SS, Service Manual

Search results

Summary of Contents for NX58R4311SS

Reviews:

Brands by name

Popular brands