Samsung MWR-SH11UN Installation Manual Download | Manualshive

Page: 8 / 20

background image

ENGLISH-8

Wired remote controller installation

Tracking your indoor unit from the wired remote controller

Displays the total number of indoor units searched

Indicates tracking in progress

1. Tracking of your wired remote controller will automatically start when you turn on the power after installation.
2. If you want to perform tracking again after installation, then press the top right corner (hidden button) of the display for

more than 7 seconds.

- The system will reset, and tracking will start again.

3. During tracking, the total number of currently searched indoor units will be displayed.
4. It may take about 3 minutes at initial installation or when you re-set the Power Master setting.

• If you want to reset the system of your wired remote controller, then press the top right corner (hidden button) of

the display for more than 7 seconds.

CAUTION

«
...
6
7
8
9
10
...
»

Summary of Contents for MWR-SH11UN





















Reviews:

No comments

Related manuals for MWR-SH11UN

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Watts Pages: 2

Brand: Absaar Pages: 36

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Datavideo Pages: 8

Brand: Jabra Pages: 4

Digiplex DGP-848

Brand: Paradox Pages: 20

Brand: Rain Bird Pages: 20

Pearldex Series

Brand: KaMo Pages: 2

Brand: Valence Tech Pages: 12

Brand: Dungs Pages: 56

Brand: Emec Pages: 8

Brand: Frico Pages: 8

Brand: GEM Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands