manualshive.com logo in svg

Samsung ML-6050, Service Manual, Page: 73 / 140

Share
Download
Samsung ML-6050 Service Manual Download Page 73

Samsung Electronics

5-41

Troubleshooting

Error code 3-100

Fault

Description

When system power is turned on, all lamps on the operator panel do not come on.

No power

Model     ML-xxxx

Check

Engine board

Cause

1. Defective harness between engine and control boards.

2. Defective harness between the control board and panel.

3. Defective fuse F151

4. Defective fuse F101

5. BD101 short. Check for the resistance value of Q102.

6. Defective U101

Solution

1. Check the connection between engine and control boards, and replace, if defective.

2. Check the connection between control board and operator panel. If defective, replace the harness.

3. Check F151 on the engine board. If open, measure the resistance between 5V and ground. If it is

below 50 ohm, it is short. 

4. Check F101 on the engine board. If open, check also :

- R114 open
- Q102, D-S, G-D, or G-S short
- Defective BD101

Remark

Others

Summary of Contents for ML-6050













































































































































Reviews:

No comments