Samsung ML-6050 Service Manual Download Page 59

Page: 59 / 140

Samsung Electronics

5-27

Troubleshooting

Error code 2-010

Fault

Description

Printing begins at wrong position on the paper.

Wrong print position

Model ML-xxxx

Check

Feed sensor actuator, LSU, Pick-up ass’y, Bracket-dust, Solenoid, Video Controller.

Cause

1. Wrong sence time caused by defective feed sensor actuator.

2. Skew:

Bad LSU-assembling
Uneven pressure force of the pick-up ass’y
Defective mechanical parts

3. Top margin;

Early feeding by the solenoid
Wrong OP1 sensor position
Wrong video controller connection

Solution

1. Replace the defective actuator.

2. Reassemble or replace the LSU.

Reassemble or replace the pick-up ass’y.
Reassemble or replace the defective mechanical parts. (for example, Bracket-dust).

3. Replace the solenoid.

Check OP1.
Check the Vedio Controller or its connection.

Remark

Others

Summary of Contents for ML-6050













































































































































Search results

Summary of Contents for ML-6050

Reviews:

Related manuals for ML-6050

Brands by name

Popular brands

Samsung ML-6050, Service Manual

Search results

Summary of Contents for ML-6050

Reviews:

Related manuals for ML-6050

Brands by name

Popular brands