Samsung ML-6050 Service Manual Download Page 55

Page: 55 / 140

5-23

Samsung Electronics

Troubleshooting

Error code 1-121

Fault

Description

One or several blank pages are printed.

When the printer turns on, several blank pages print.

Partial black image

Model ML-xxxx

Check

Control board

Cause

Defective control board

Solution

1. Perform the engine self test using DCU. If blank page prints, the control board is defective. If the

printer works normally, refer to next solution (2). If the control board is defective, check the
connection on the control board, QP1700 pin 125, and 202.

2. If blank page is printed one time or continuously, check that the video controller oscillates properly

at 47.7789 MHz. (lower than 0.75V, higher than 3.5V)

3. If blank pages prints continuously when the printer turns on, check the CPU works properly, and

replace if defective.

Remark

Others

Summary of Contents for ML-6050













































































































































Search results

Summary of Contents for ML-6050

Reviews:

Related manuals for ML-6050

Brands by name

Popular brands

Samsung ML-6050, Service Manual

Search results

Summary of Contents for ML-6050

Reviews:

Related manuals for ML-6050

Brands by name

Popular brands