Samsung HT-AS700 Instruction Manual Download

Page: 50 / 55

Before Calling for Service

Symptom

Check Remedy

Can't turn it on.

It does not work when the
button is pressed.

Sound is not produced.

Picture does not appear when
the function is selected.

•

Is the power code plugged into the outlet?

•

Isn’t the air too dry to cause

electrostatics?

•

Are the speaker and external

component connected properly?

•

Does the Mute function work?

•

Is the volume set to minimum?

•

Is the speaker setup selected to

NONE?

•

Isn’t the external component connected

properly?

•

Connect the power plug to the outlet.

•

Disconnect the power plug and connect it

again.

•

Properly connect it.

•

Properly connect it.

•

Press Mute button to cancel the function.

•

Adjust the volume.

•

Refer to page 17~18 to select LARGE,

SMALL or YES.

There is no sound from

center speaker

•

Is the center speaker connected properly?

•

Is C.SPK (Center) selected to NONE in

Speaker Setup?

•

Is the Surround Mode selected to Stereo?

•

Refer to page 9~10 to connect it properly.

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Refer to page 27~38 to select other

Surround Mode.

Remote controller does not
work.

There is no sound from rear

speaker.

The sound from each device
is changed during stereo
playback.

Can't receive broadcasting.

•

Is AM or FM antenna connected

properly?

•

Are the batteries exhausted?

•

Is the distance between remote

control and main unit proper?

•

Is the rear speaker connected

properly?

•

Is S.SPK (Rear) set to NONE in

Speaker Setup?

•

Is Surround Mode selected to Stereo?

•

Refer to page 17~18 to connect it properly.

•

Refer to page 17~18 to select LARGE or

SMALL.

•

Refer to page 27~38 to select other

Surround Mode.

•

Replace with new batteries.

•

Operate at close distance.

•

Properly connect the antenna.

•

If the input strength of antenna connector is

weak, install the FM antenna at the place
with good reception.

•

Is the left/right speaker or left/right

input/output code connected
properly?

•

Check the left/right channel and properly

connect it.

Summary of Contents for HT-AS700
























































Search results

Summary of Contents for HT-AS700

Reviews:

Related manuals for HT-AS700

Brands by name

Popular brands

Samsung HT-AS700, Instruction Manual

Search results

Summary of Contents for HT-AS700

Reviews:

Related manuals for HT-AS700

Brands by name

Popular brands