Samsung DW60A6080 Series Repair Manual Download

Page: 3 / 32

Tools For Removal And Reassembly _ 3

1. TOOLS FOR REMOVAL AND REASSEMBLY

Tool image

No.

Tool

Type

Remarks

①

Adjustable Wrench

②

Open-end Wrench

1-7/16”

③

Vice Pliers

④

Others

(screwdriver, nipper, long nose pliers)

Common tools for servicing

Screwdriver – Phillip, Flat, Torx T15

⑤

Ear clamping tool

In reassembling of the clamp-bend(ear clamp) using our

SVC part, this tool is needed.

NOTE

Preparation for parts replacement

1. Remove the residual water inside the product. (Drain the water by operating the drain pump)

2. Close the water supply valve.

3. Turn off the power & disconnect the power cable.

You must turn off the circuit breaker connected to the product.

4. Pull out the unit from the sink and lay it on the floor.

Be careful of the drain hose when pulling out the unit.

5. For materials and repair information related to self-repair, refer to the web site:

www.samsung.com/support

Summary of Contents for DW60A6080 Series

































Search results

Summary of Contents for DW60A6080 Series

Reviews:

Related manuals for DW60A6080 Series

Brands by name

Popular brands

Samsung DW60A6080 Series, Repair Manual

Search results

Summary of Contents for DW60A6080 Series

Reviews:

Related manuals for DW60A6080 Series

Brands by name

Popular brands