Samsung DW60A6080 Series Repair Manual Download | Manualshive

Page: 26 / 32

background image

26 _ Disassembly and Reassembly

Part

Figure

Description

BASKET MIDDLE

GUIDE BUTTON

HOLDER GUIDE TINE

5. Release the 4 hooks of HOLDER GUIDE TINE and

separate it from the BASKET MIDDLE.

6. Push the GUIDE BUTTON to separate it from the

HOLDER GUIDE TINE.

WARNING

Do not do this work without safety gloves. It may

cause injury from sharp edges.

CAUTION

Be careful not to break the hooks.

1

2

HOLDER GUIDE TINE-UP

WIRE GUIDE TINE

7. Release the hook of the HOLDER GUIDE TINE-

UP to separate the WIRE GUIDE TINE from the

BASKET MIDDLE.

WARNING

Do not do this work without safety gloves. It may

cause injury from sharp edges.

CAUTION

Be careful not to break the hooks.

[ASSEMBLY]

Reassembly is the reverse order of disassembly.

Carefully assemble the assembly position of the

HOLDER TINE-UP and the HOLDER GUIDE

TINE-UP.

«
...
24
25
26
27
28
...
»

Summary of Contents for DW60A6080 Series

































Reviews:

No comments

Related manuals for DW60A6080 Series

Brand: GE Pages: 2

Spacemaker WSLP1500JWW

Brand: GE Pages: 3

Brand: Kärcher Pages: 9

Brand: lamber Pages: 46

Millennia MDW24S

Brand: Dacor Pages: 29

Brand: Dacor Pages: 24

Brand: Gaggenau Pages: 22

Brand: Gaggenau Pages: 34

Brand: Samsung Pages: 96

Brand: Euromaid Pages: 32

Brand: Bauknecht Pages: 14

DISHDRAWER DD24SHI9

Brand: Fisher & Paykel Pages: 22

EVOconcept CCO-120DCW

Brand: Fagor Pages: 156

Brand: Gaggenau Pages: 52

AQUALTIS AQ9D 48 X

Brand: Hotpoint Ariston Pages: 48

Brand: Technika Pages: 42

Brand: Hotpoint Pages: 2

Profile PDWT400R

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands