Samsung DB32E User Manual Download

Page: 190 / 205

190

Other issue

Caption

is grayed out and not selectable.

If the selected input source is not

Caption

cannot be selected from the

System

menu.

Caption

can be enabled from a source device.

The product smells like plastic.

The plastic smell is normal and disappears over time.

The monitor appears tilted.

Remove and then attach the stand again to the product.

Audio or video cuts out intermittently.

Check the cable connection and connect it again if required.

Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it
is recommended to use right-angle cables.

Small particles are found on the edges of the product.

The particles are part of the product design. The product is not defective.

The

PIP

menu is not available.

The menu is enabled or disabled depending on the

Source

mode.

When I try to change the PC resolution, a message "

The

defined resolution is not currently supported.

" appears.

The message "

The defined resolution is not currently supported.

" appears if the input source

resolution exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.

There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.

DVI cables do not transmit sound data.
Make sure to connect the audio cable to the correct input jack to enable audio.

HDMI Black Level

is not functioning properly on an HDMI

device with YCbCr output.

This function is available only when a source device, such as a DVD player and STB, is connected to the
product via an HDMI (RGB signal) cable.

Summary of Contents for DB32E














































































































































































































Search results

Summary of Contents for DB32E

Reviews:

Related manuals for DB32E

Brands by name

Popular brands

Samsung DB32E, User Manual

Search results

Summary of Contents for DB32E

Reviews:

Related manuals for DB32E

Brands by name

Popular brands