manualshive.com logo in svg

Samsung CLP-300N/XEU, Service Manual

Share
Download
Samsung CLP-300N/XEU Service Manual Download Page 89

Samsung Electronics

Service Manual

Troubleshooting

7-10

Loose toner

Clean the inside of the printer.
Check the paper type and quality. 
Install a new toner cartridge. 
If the problem persists, the printer may require repair. Contact a service representative.

Problem 

Solution

Character Voids

Character voids are white areas within characters that should be solid black:

You may be printing on the wrong surface of the paper. Remove the paper and turn it
over.
The paper may not meet paper specifications. 

A

Horizontal stripes

If horizontally aligned color or black streaks or smears appear:

A toner cartridge may be installed improperly. 
Remove the toner cartridge and reinsert.
A toner cartridge may be defective. Install a new toner cartridge.
If the problem persists, the printer may require repair. Contact a service representative.

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

Curl

If the printed paper is curled or paper does not feed into the printer:

Turn the stack of paper over in the paper tray. Also try rotating the paper 180° in the
tray.

Summary of Contents for CLP-300N/XEU










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands