Samsung CLP-300N/XEU Service Manual Download Page 74

Page: 74 / 137

Samsung Electronics

Service Manual

Alignment and Adjustmens

6-1

6.6.3.1 Motor Test

6.6.3.2 Solenoid Test

Item

Discription

Main Motor

If motor lock signal is normal, “Successed” message will be displayed.
When motor lock signal is abnormal, “failed” message will be displayed.
When “Upper Level” is pushed, “off ” message will be displayed.

Item

Discription

Dev Clutch

When select key is pushed, Dev Clutch ON message will be displayed.

Upper Level is pushed, Dev Clutch Off message will be displayed.

Y Relay

When select key is pushed, Y Relay ON message will be displayed. Upper
Level is pushed, Y Relay Off message will be displayed on.

M Relay

When select key is pushed, M Relay ON message will be displayed. Upper
Level is pushed, M Relay Off message will be displayed.

C Relay

When select key is pushed, C Relay ON message will be displayed. Upper
Level is pushed, C Relay Off message will be displayed.

K Relay

When select key is pushed, K Relay ON message will be displayed. Upper
Level is pushed, K Relay Off message will be displayed.

Y Toner

When select key is pushed, Y Toner ON message will be displayed. Upper
Level is pushed, Y Toner Off message will be displayed.

M Toner

When select key is pushed, M Toner ON message will be displayed. Upper
Level is pushed, M Toner Off message will be displayed.

C Toner

When select key is pushed, C Toner ON message will be displayed. Upper
Level is pushed, C Toner Off message will be displayed.

K Toner

When select key is pushed, K Toner ON message will be displayed. Upper
Level is pushed, K Toner Off message will be displayed.

Regi Clutch

When select key is pushed, REGI Clutch ON message will be displayed.

Upper Level is pushed, REGI Clutch Off message will be displayed.

T2 Clutch

When select key is pushed, T2 Clutch ON message will be displayed.

Upper Level is pushed, T2 Clutch Off message will be displayed.

ITB Clutch

When select key is pushed, ITB Clutch ON message will be displayed.

Upper Level is pushed, ITB Clutch Off message will be displayed.

Tray1 Clutch

When select key is pushed, Tray1 Clutch ON message will be displayed.

Upper Level is pushed, Tray1 Clutch Off message will be displayed.

Regi. Sensor

If actuator is checked by sensor, "Without Paper" message will be displayed. if
not, "With Paper" message will be.

Exit Sensor

If actuator is checked by sensor, "Without Paper" message will be displayed. if
not, "With Paper" message will be.

Waste Box

If waste Box exists , Installed message will be displayed.
If not, Not Installed message will be.

Cover

If cover is opened, " Opened message will be displayed.
If not, "Closed" message will be.

Tray1 Empty

If paper exists in the tray, "With Paper" will be displayed.
If not, "Without Paper" message will be.

Summary of Contents for CLP-300N/XEU










































































































































Search results

Summary of Contents for CLP-300N/XEU

Reviews:

Brands by name

Popular brands

Samsung CLP-300N/XEU, Service Manual

Search results

Summary of Contents for CLP-300N/XEU

Reviews:

Brands by name

Popular brands