Samsung CLP-300N/XEU Service Manual Download Page 78

Page: 78 / 137

Samsung Electronics

Service Manual

Alignment and Adjustmens

6-1

- Paper Jam at the paper exit area

There is a paper at exit area

After cover Open , Paper must be removed, and then close the cover

- Motor Lock Error

Motor does not run or runs abnormal speed

Motor or Main board must be checked

- LSU Motor Lock Error

LSU motor does not run or runs abnormal speed

Hsync is not detected

LSU or Main board must be checked

- Transfer Belt Error

ITB home sensor is not checked for a normal time

ITB must be checked

- Fuser Over Heat error

Temperature of fuser is high

Fuser or Main board must be checked

- Fuser Low Heat error

Temperature of fuser is low

Fuser or Main board must be checked

- Dev. Home error

Home of Development is not checked or checked at the abnormal time

Clutch of Development or Main board must be checked

- ADC not Confirm Error

Signal of confirmation for ADC is not detected

Main board must be checked

Summary of Contents for CLP-300N/XEU










































































































































Search results

Summary of Contents for CLP-300N/XEU

Reviews:

Brands by name

Popular brands

Samsung CLP-300N/XEU, Service Manual

Search results

Summary of Contents for CLP-300N/XEU

Reviews:

Brands by name

Popular brands