background image

E-

2

Safety Precautions

You should take the following safety precautions when using your air conditioner.

Users should not install the air conditioner by themselves. 
Ask the dealer or authorized company to install the air conditioner
except the window-type air conditioner in U.S.A and Canada. 

If you don’t install the air conditioner properly, it may cause a fire, 
a water leakage or an electric shock.

You must install the air conditioner according to the national wiring
regulations and safety regulations.

Install the indoor unit higher than 2.5m from the floor to avoid the
injury caused by the operation of the fan. (except the window-type
air conditioner)

The manufacturer is not responsible for the accidents or injury
caused by an incorrect installation. 

When installing the built-in type air conditioner, keep all electric
cables such as the power cable and the connection cord in pipes,
ducts, or cable channels to protect them from the danger of impact
or any other incidents. 

WARNING

I

NSTALLING THE

AIR CONDITIONER

If the power cord of the air conditioner is damaged, it must be
replaced by the manufacturer or a qualified person in order to avoid
a hazard.

The air conditioner must be plugged into an independent circuit if
applicable or connect the power cable to the auxiliary circuit breaker. 
An all pole disconnection from the power supply must be incorporated
in the fixed wiring with a contact opening of >3mm. 

Do not extend an electric cord to the air conditioner. 

The air conditioner must be plugged in after you complete the 
installation. 

P

OWER SUPPLY AND

CIRCUIT BREAKER

• 

If you don’t follow the safety precautions, you may get the risk of an electric
shock, injury or death.

The manufacturer or qualified service personnel must install this air conditioner.

• 

Unplug the electric power before repairing, installing or cleaning.

 AQT18WJWB IM_E_20227  10/25/04 1:34 PM  Page 2

Summary of Contents for AQ18FA Series
















Reviews: