Samsung AM AXV Series Installation Manual Download Page 41

Page: 41 / 68

English

Instal

lation Pr

edur

Power wiring diagram

Supplying 3 phase 4 wires (380-415 V~)

3 phase 4 wires

(380-415 V~)

MCCB+

ELB

MCCB+

ELB

ELCB

Main unit

Sub unit

Main unit

Sub unit 1

Sub unit 2

Single phase 2 wires

(220-240 V~)

Grounding

Wired remote

controller

Wired remote

controller

Communication

cable (Outdoor unit ~

Outdoor unit)

Communication cable

(Outdoor unit ~ Indoor

unit)

Wired remote
controller

Communication cable

(Outdoor unit ~ Indoor

unit)

Communication cable

(Outdoor unit ~ Outdoor

unit)

3 phase 4wires 380 - 415 V~

MCCB+

ELB

MCCB+

ELB

MCCB+

ELB

MCCB+

ELB

ELCB

Main unit

Sub unit

Main unit

Sub unit 1

Sub unit 2

Single phase 2 wires

(220-240 V~)

Grounding

Wired remote

controller

Wired remote

controller

Communication

cable (Outdoor unit ~

Outdoor unit)

Communication

cable (Outdoor unit ~

Indoor unit)

Wired remote
controller

Communication cable

(Outdoor unit ~ Indoor

unit)

Communication cable

(Outdoor unit ~ Outdoor

unit)

•

Connect a power cable of the outdoor unit after checking that R-S-T-N (3 phase 4 wire) is properly connected. (If the 380-415 V power

is supplied to the N phase, PCB and other electrical part will be damaged.)

• Communication cable between indoor and outdoor units and communication cable between outdoor units has no polarity.
• Arrange the cables with a cable tie.

※

ELCB and ELB must be installed since there is risk of electric shock or fire when they are not installed.

Summary of Contents for AM AXV Series





































































Search results

Summary of Contents for AM AXV Series

Reviews:

Related manuals for AM AXV Series

Brands by name

Popular brands

Samsung AM AXV Series, Installation Manual

Search results

Summary of Contents for AM AXV Series

Reviews:

Related manuals for AM AXV Series

Brands by name

Popular brands