Samsung AC***FB4DEH Installation Manual Download Page 4

Page: 4 / 28

Deciding on where to install the indoor unit

Preparation for installation



The following accessories are supplied with the indoor unit.

The type and quantity may differ depending on the specifications.

Indoor unit

Space requirements for indoor unit

Accessories



There must be no obstacles near the air inlet and outlet.



Install the indoor unit on a ceiling that can support its weight.



Maintain sufficient clearance around the indoor unit.



Make sure that the water dripping from the drain hose runs away correctly and safely.



The indoor unit must be installed in this way, that they are out of public access. (Not touchable by the users)

Insulation cover

band

Insulation pipe

Cable-tie

Drain hose

Installation

manual

Clamp

• If you install the cassette type indoor unit on the ceiling with humidity over 80%, you must apply extra 10mm of

polyethylene foam or other insulation with similar material on the body of the indoor unit.

CAC CASSETTE TYPE 유럽-터키향_IM_32787A-14_EN.indd 4

2016-05-26 오후 5:17:23

Summary of Contents for AC***FB4DEH





























Search results

Summary of Contents for AC***FB4DEH

Reviews:

Related manuals for AC***FB4DEH

Brands by name

Popular brands

Samsung AC***FB4DEH, Installation Manual

Search results

Summary of Contents for AC***FB4DEH

Reviews:

Related manuals for AC***FB4DEH

Brands by name

Popular brands