manualshive.com logo in svg

Samson 3381 Series, Mounting And Operating Instructions, Page: 2 / 48

Share
Download
Samson 3381 Series Mounting And Operating Instructions Download Page 2

 Definition of signal words 

Hazardous situations which, if not avoided, 
will result in death or serious injury

Hazardous situations which, if not avoided, 
could result in death or serious injury

Property damage message or malfunction

Additional information

Recommended action

DANGER

!

WARNING

!

NOTICE

!

Note

Tip

 

EB 8084 EN

Note on these mounting and operating instructions

These mounting and operating instructions assist you in mounting and operating the device 
safely. The instructions are binding for handling SAMSON devices. The images shown in 
these instructions are for illustration purposes only. The actual product may vary.

 

Î

For the safe and proper use of these instructions, read them carefully and keep them for 
later reference.

 

Î

If you have any questions about these instructions, contact SAMSON‘s After-sales Service 
([email protected]).

Documents relating to the device, such as the mounting and operating 
instructions, are available on our website at 

www.samsongroup.com > 

Service & Support > Downloads > Documentation

.

Summary of Contents for 3381 Series

















































Reviews:

No comments