background image

36  |  SAMLEX AMERICA INC.    

 

LeD Display

other Symptoms

possible cause(s)

remedy

•   Green LED 

“CHArGer” 

(7, Fig 3.1) is OFF

•   Green LED 

“INVerTer” 

(8, Fig 3.1) is ON 

•  Charger has stopped 
•   Grid voltage is avail

-

able at the power cord

•  AC output is available 

5A fuse (5, Fig 3.1) feed

-

ing the Charger Section 
has blown. As a result, 
Grid AC Input Detect 
Circuit in the Charger 
Section has  detected 
Grid AC input failure re-
sulting in transfer from 
Grid to Inverter   

Replace 5A fuse (5, 

fig 3.1). If fuse blows 
again, the battery 
Charger Section is likely 
to be defective. Call 
Tech Support

•  Charger has stopped
•   Grid voltage is NOT 

available at the 
power cord 

•  AC output is available

Grid has failed or 
the breaker / switch 
supplying input to the 
GfCI protected Grid AC 
outlet has tripped or has 
been switched off. As 
a result, Grid AC Input 
Detect Circuit in the 
battery Charger Section 
has detected Grid AC 
input failure resulting 
in transfer from Grid to 
Inverter   

Confirm if Grid has 
failed. If not, check if 
the breaker / switch 
supplying the GfCI pro-
tected Grid AC outlet 
has tripped or has been 
switched off

•   Green LED 

“CHArGer” 

(7, Fig 3.1) is OFF

•   Red LED “FAULT” 

(9, Fig 3.1) is ON 

•   Charger has stopped
•   Grid voltage is NOT 

available at the 
power cord 

•   AC output is NOT 

available

There is leakage or 
Neutral to Ground bond 
on AC load side. 

•   First, the GFCI 

protected AC outlet 
supplying Grid power 
will trip. As a result, 
Grid AC Input Detect 
Circuit in the Charger 
Section will detect 
Grid AC input failure 
resulting in transfer 
from Grid to Inverter  

•   Once the load is 

transferred from Grid 
to the Inverter, the 
Inverter  will shut 
down due to leakage 
or Neutral to Ground 
bond on the load side  

•   Check for leakage / 

Neutral to Ground 
bond on the AC load 
side

•   Reset the GFCI pro

-

tected AC outlet sup-
plying Grid power

•   The Inverter Section 

will remain latched 
in off condition. 
To reset, switch off 
the Inverter oN/off 

Switch (3, Fig 3.1), 

wait for  3 minutes 
and switch oN again

SeCTIOn 6  |   

Protections, Monitoring 
& Troubleshooting

table 6.2 protections & monitoring: Battery charger / Grid ac power pass through 
mode (continued)

Summary of Contents for SAM Series









































Reviews: