Samoa PUMPMASTER 3+3 Parts And Technical Service Manual Download Page 6

Samoa Industrial, S.A. - Box 103  Alto Pumarín – 33211 Asturias Spain – Tel. +34 985 381 488 – Fax. +34 985 384 163 

 

 

 

 

 
 

 

 
 

 

1.  Die Pumpe auf einer Werkbank waagrecht am Saugrohr in einen Schraubstock spannen.  
2.  Den Luftmotor vom Saugrohr (44) abschrauben und herausziehen, bis der Stift (34) sichtbar ist (Bild 4). 
3.  Den Stift entfernen und die Gewindestange (43) abschrauben, bis sie abnehmbar ist (Bild 5).  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

1.  Unthread the plug (23) and remove the circlip (13), the muffler (14) and the muffler support (15). 
2.  Remove the distributor axle (21) (fig. 6). 
3.  Unthread the screw (8) completely and remove the distributor bushing (16) carefully.  

4.  Lubricate the new distributor bushing with its O-rings, insert it from the side of the plug (23) and hold something to stop 

it at the side of the muffler(14). Be very careful so that the bushing does not get damaged.   

5.  Assemble the rest following previous instructions, reversing each step. 
 
 
1.  Desenroscar el tapón (23) y quitar el anillo seguridad (13), el silenciador (14) y el suplemento filtro(15). 
2.  Quitar el eje distribuidor (21) (Fig. 6).  
3.  Soltar el tornillo (8) por completo y usar un botador para cuidadosamente quitar la camisa del distribuidor (16). 
4.  Lubricar y colocar la nueva camisa con sus juntas, insertándola desde el lado del tapón (23), teniendo un tope en el lado 

del silenciador(14). Procurar no dañar la camisa. 

5.  Volver a montar el resto en orden contrario. 

 
 

 
1.  Desserrer le bouchon (23) et retirer l’anneau de sécurité (13), le silencieux (14) ainsi que la portée du filtre (15). 
2.  Démonter l’axe du distributeur (21) (Fig. 6). 
3.  Dévisser totalement la vis (8) et retirer soigneusement le manchon du distributeur (16) à l’aide d’un repoussoir.  
4.  Lubrifier et placer le nouveau manchon ainsi que ses joints toriques en l’introduisant sur le côté du bouchon (23), en 

tenant compte de la butée du silencieux (14) et en prenant soin de ne pas l’endommager. 

5.  Remonter la pompe en suivant le processus inverse. 

 
 
 
 

 

6

 

 840806 

R03/05

 

 

Separate the air motor from the pump/ Como separar el motor de aire de la bomba/  

Comment séparer le moteur d’air de la pompe/ Trennen des Luftmotors von der Pumpe

 

Air distributor/ Distribuidor de aire/ Distributeur d’air/ Luftverteiler 

 

GB 

Repair and cleaning procedure/ Procedimientos de reparación y limpieza/  

Instructions de réparation et de nettoyage/ Reparatur- und Reinigungsanleitung

 

Fig. 4 

Fig. 5 

Summary of Contents for PUMPMASTER 3+3















Reviews: