manualshive.com logo in svg

Samoa LARIUS OMEGA, Operating And Maintenance Manual, Page: 9 / 38

Share
Download
Samoa LARIUS OMEGA Operating And Maintenance Manual Download Page 9

www.larius.com

9

Omega 23:1-30:1

ED.

 04 - 09/2021 - Cod. 150150

     

•   NEVER  POINT  THE  SPRAY  GUN  AT  YOURSELVES  OR  AT 

OTHER PEOPLE. THE CONTACT WITH THE CASTING CAN 
CAUSE SERIOUS INJURIES.

•   IN CASE OF INjURIES CAUSED BY THE GUN CASTING, SEEK 

IMMEDIATE MEDICAL ADVICE SPECIFYING THE TYPE OF 
THE PRODUCT INJECTED. NEVER UNDERVALUE A WOUND 
CAUSED BY THE INJECTION OF A FLUID

•   ALWAYS  DISCONNECT  THE  SUPPLY  AND  RELEASE  THE 

PRESSURE IN THE CIRCUIT BEFORE PERFORMING ANY 
CHECK OR PART REPLACEMENT OF THE EQUIPMENT.

•   NEVER  MODIFY  ANY  PART  IN  THE  EQUIPMENT.  CHECK 

REGULARLY THE COMPONENTS OF THE SYSTEM. REPLACE 
THE PARTS DAMAGED OR WORN.

•   IF  PROVIDED) 

TIGHTEN AND CHECK ALL THE FITTINGS 

FOR 

connecTIon BeTween pump, flexIBle hose AnD 

sprAy Gun Before usInG The equIpmenT

.

•   

The fluID conTAIneD In The flexIBle hose cAn Be 
very DAnGerous. hAnDle The flexIBle hose cAre-
fully. Do noT pull The flexIBle hose To move The 
equIpmenT. never use A DAmAGeD or A repAIreD 
flexIBle hose.

•   

never sprAy over flAmmABle proDucTs or sol-
venTs In closeD plAces.

•   

never use The ToolInG In presence of poTenTIAlly 
explosIve GAs.

The high speed of travel of the product in the hose 

can create static electricity through discharges 

and sparks. It is suggested to earth the equipment. 

The pump is earthed through the earth cable of 

the supply. 

The gun is earthed through the high pressure 

flexible hose.  

All the conductors near the work area must be 

earthed.

Avoid approaching too much to the pump piston 
rod when the pump is working or under pressure. 
A sudden movement of the piston rod can cause 
wounds or finger squashing.

H

Fig. 1H

SISTEMA ANTIGELO

The machine is equipped with an anti-freeze
system that allows it to work even at very low
temperatures. However, after a few minutes of
operation, the upper metal outer surface cools
dramatically. Avoid touching the area indicated.
Contact of the skin with the low-temperature area
may cause frostbite. Common working clothes
and leather gloves provide adequate protection.

SIf the product to be used is toxic avoid inhalationa 
and contact, by using protective gloves, goggles 
and suitable face shiedls
Take proper safety measures for the protection 
of hearing in case of work near the plant.

Summary of Contents for LARIUS OMEGA







































Reviews:

No comments