manualshive.com logo in svg

Samoa LARIUS OMEGA, Operating And Maintenance Manual, Page: 5 / 38

Share
Download
Samoa LARIUS OMEGA Operating And Maintenance Manual Download Page 5

www.larius.com

5

Omega 23:1-30:1

ED.

 04 - 09/2021 - Cod. 150150

B

C

PRINCIPIO DI FUNZIONAMENTO

OMEGA

 pump 

23:1 

(or 

30:1)

 is a pneumatic pump to be used in the high pressure painting without air (Airless) or for transferring of 

fluids in case of more stations of usage.
OMEGA pump is essentially constituted of an air motor and a structure called «material pumping group» or simply «pumping group».
In the pneumatic motor, compressed air causes the vertical reciprocating movement of the motor piston; this movement is transmitted 
through a connecting rod to the material pumping piston.
So doing the pump sucks the fluid and pushes it to the outlet.
The ratio 23:1 (o 30:1) means that the outlet pressure of fluid is 23 (o 30) times higher than the pump feed air pressure.

Parts of the pump in contact with the material

Pumping group: galvanized carbon steel and cast iron or stainless 

steel AISI 303 and 420B
Sealing balls: stainless steel AISI 420B

Gaskets: PTFE or nitrile or delrin or vulkollan

Other parts of the pump

Support and cylinder for pneumatic motor: aluminium

Covering: sheet FE37

Motor piston and roller pushing mount: cast iron

TECHNICAL DATA

OMEGA 23:1

OMEGA 23:1

Pump feed air pressure

3-7 bar (40-90 psi)

3-7 bar (40-90 psi)

Masimum pressure of the product

161 bar (2300 psi)

210 bar (3050 psi)

Feed air inlet

3/4” GAS (M)

3/4” GAS (M)

Maximum delivery

14 l/min (3,7 gpm)

12 l/min (3,2 gpm)

Cycles per litre

4

5

Maximum cycles per minute

60

60

Material outlet

1” conico GAS (F)

1” conico GAS (F)

Weight

55 kg

55 kg

Noise pressure level

<90 dB (A)

<90 dB (A)

Total height

1110 mm

1110 mm

Always observe these instructions carefully 
when evaluating the product compatibility and 
in case of disposal of some parts of the pump 
no more usable, in order to meet the envi-
ronmental regulations on recycling process.

Summary of Contents for LARIUS OMEGA







































Reviews:

No comments