manualshive.com logo in svg

Samoa LARIUS OMEGA, Operating And Maintenance Manual, Page: 10 / 38

Share
Download
Samoa LARIUS OMEGA Operating And Maintenance Manual Download Page 10

www.larius.com

10

Omega 23:1-30:1

ED.

 04 - 09/2021 - Cod. 150150

F2

F1

*

The 

OMEGA

 pump is generally supplied on support for wall 

fastening or on trolley or on double post ram.

For the correct fastening of the pump on other structures use 
the 4 holes placed at the base of the pneumatic motor (see the 
illustration for dimensions).

Fig. 2H

L

I

Fig. 3I

*Int. holes

In condizioni climatiche rigide è necessario inserire del liquido 
antigelo (

F1

) all'interno del gruppo FRL (

F2

)

If 100% pure antifreeze liquid is used, it is recommended the 

dilution shown in the table.

DILUITION RECOMMENDED FOR PURE PRODUCT

% water diluition

°C, environmental temperature

10%

-5

20%

-10

30%

-20

40%

-25

50%

-37

60%

-50

 

NOTE

When the pump is used in places with higher 

temperatures, the phenomenon indicated 

above may not occur and therefore it is not 

necessary to use antifreeze.

SETTING UP

TYPICAL INSTALLATION

CONNECTION TO THE FEED AIR

• 

For pump feed use a hose with an internal diameter no 
lower than 20 mm.

Install at the pump inlet an air pressure regulator 
(it is suggested complete with condensate filter 
and lubricator). The outlet pressure of the material 
is 23 times (OMEGA 23:1) or 30 times (omega 30:1) 
the inlet pressure of the pump feed air. Therefore, 
it is extremely important to adjust the value of the 
feed air pressure.

COLLEGAMENTO DEL TUBO USCITA MATERIALE

• 

Connect the high pressure hose at the outlet of the pump.
It is recommended to tighten the fittings.

PUMP FASTENING ON THE HOIST

• 

For the correct fastening of the pump on the ram, follow the 
procedure described in the manual for use and maintenance 

of the double post ram.

Summary of Contents for LARIUS OMEGA







































Reviews:

No comments