Samoa 560312 Service Manual Download Page 7

7

R. 06/18  856 827

 SAMOA Industrial, S.A. · Pol. Ind. Porceyo,  I-14 · Camino del Fontán, 831 · 33392 -  Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com

2018_06_26-13:00

EN

HANDLING–TRANSPORT

HANDLING

309201 - 560311 e 560312 - 560313 tanks come with handles for 
lifting; moreover, only the 560312 - 560313 can also can be lifted, 
laden or not, exclusively via trans–pallets or forklift with forks 
completely inserted into the tracks highlighted in the schemes below.

Passages for forklift forks housing in 560312 - 560313

Pay attention to the effects of repeated rubbing produced 
by forks at the bottom of the container because usury, over 
time, could lead to structural weakening and impair the 
grip. It is therefore important to careful use of lifting 
equipment, and periodically check the status of the bottom 
of the container.

!

Lifts by different means or hooking 
the tank in points other than those 
expressly provided for and highlighted 
with appropriate pictograms are not 
allowed.

Top handle for gripping and lifting Lower housing for lifting.

!

Weight distribution on handle during towing.

ROAD TRANSPORT

The containers referred to in this manual are not subject to 
the requirements of ADR provided for the transport of 
dangerous goods, including those relating to ADR labelling 
and reporting of the material transported.

It is anyway advisable to equip the tanks with the following 
hazard pictograms:

hazard pictograms of material harmful to the environment.

The safety of carriage must be anyway guaranteed and the 
prescriptions of art. 164 of the Traffic Laws about “STOWAGE OF 
LOAD ON SAMOA_AdBlue_Rev.0 del 04/2018 11 EN VEHICLES” 
must be observed. Therefore:
- The containers should be kept clean, free from residue of 

hazardous material adhering to its exterior.

-  The containers must be firmly anchored to the floor of the 

vehicle, using belts of adequate form and adequate strength 
so as to avoid any slippage or displacement on the load floor

-  Avoid the presence on the vehicle’s cargo area of rags or other 

inflammable objects.

- The shut–off valves (if any) must be kept closed during 

transport.

-  The containers must be placed on the loading surface so that 

the maximum loads on the axles of the vehicle are not 
exceeded.

-  The driver must take prudent and cautious guidance especially 

in the case of partial loads, because the fluctuations of liquid, 
while taking into account the limited volume of the tank, can 
negatively affect road holding of the vehicle.

STACKING

There is no possibility of stacking during transport.
As regards the storage phase, different rules apply depending on the model of the tank:
- For 560312 - 560313 containers, stacking of max. n. 1 laden contained and n. 3 empty containers is admitted.
- For 309201 - 560311 containers, there is no possibility of stacking

309201 - 560311 series containers are equipped with vacuum lifting handles both on the upper part and at the bottom.

Summary of Contents for 560312

























Reviews: