Sam4s ER-285M Operator'S Manual Download Page 117

Page: 117 / 218

SAM4s ER-285M Operator's and Program Manual v1.4

Service Mode Reference Guide

•

117

Self Tests

Self-tests can be performed to check the functions of the register.

Turn the control lock to the

position.

Enter the test number from the chart below

and press the

SBTL

key.

Test Key

Sequence

Results/Instructions

Printer

10 SBTL

The receipt printer generates a printer test pattern.

Display

11 SBTL

Displays illuminate a test pattern.

Keyboard

12 SBTL

Press any key. The key’s hex value is displayed.
Turn key lock to end the test.

Mode Lock

13 SBTL

Turn the mode lock to display the lock position.
Return the key to S to end the test.

RS232C Port 1
RS232C Port 2
RS232C Port 3

14 SBTL
24 SBTL
34 SBTL

Loop back connector must be connected.
Displays “232 Port Good” if successful; displays
“232 Port No Good” if unsuccessful.

Endless
Printing

15 SBTL
16 SBTL

The receipt prints a sample ticket. The print is
repeated until the key lock is turned.

SD Card

17 SBTL

Insert an SD card. After the test is complete, the
display reads “TEST SD CARD INSERTED”.
Press Clear. Card information is printed.

MCR

18 SBTL

Swipe card to test. If successful, “TRK 1 OK
TRK 2 OK” displays. Track data is printed.

SBTL

Summary of Contents for ER-285M



























































































































































































































Search results

Summary of Contents for ER-285M

Reviews:

Related manuals for ER-285M

Brands by name

Popular brands

Sam4s ER-285M, Operator'S Manual

Search results

Summary of Contents for ER-285M

Reviews:

Related manuals for ER-285M

Brands by name

Popular brands