manualshive.com logo in svg

Sam4s ER-265, Operator'S And Programming Manual

Share
Download
Sam4s ER-265 Operator'S And Programming Manual Download Page 83

SAM4s ER-265 Operator's and Programming Manual v1.14 

Advanced Programming Instructions   

  83 

Programming Descriptions 

Customer Logo 

Without otherwise programming, the customer logo will print a two line message at the top of each 
receipt: 

THANK-YOU 

CALL AGAIN 

If you wish, you can replace this message with your own custom message.    You can have both a 
preamble message (top of receipt) and a postamble message (bottom of receipt).    Each can be up to 
6 lines long. 

Programming a Custom Logo: 

You can also program your logo using the Program Overlay method.    See “Program Overlay” on 
page 88. 

1.

 

Turn the control lock to the 

PGM

 position. 

2.

 

Press the 

X/TIME 

key. 

3.

 

Refer to the “Code Table” on page 87 and enter the two digits that represent each 
character you wish.    You can enter up to 32 character codes for each line.     

4.

 

Press the 

X/TIME 

key. 

5.

 

Enter the two digit number that represents the line of the message you wish to program: 

11 ~ 16 : 1

st

 Line ~ 6

th

 Line (Preamble Logo) 

21 ~ 26 : 1

st

 Line ~ 6

th

 Line (Postamble Logo) 

6.

 

Press the 

CHECK

 

TEND 

key 

7.

 

Repeat from step 2 for each line you are programming. 

8.

 

Press the 

CASH/TEND

 key to end programming. 

Logo Programming Flowchart 

 

CHECK/ 

TEND 

CASH/

TEND

Repeat for each Line of the Logo

 

 

 

Up to 32

2-digit 

character 

codes

X/TIME 

 

Line # 

Code

 

X/TIME

 

Summary of Contents for ER-265











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands