background image

- 4 -

[How to Operate Steam Cleaner]
In the very initial stage of operation, it discharges water rather than steam. 
Place a steam nozzle to an additional water tank or drain (prepare a spare water tank)
Press the steam button to start working.
Pushing the steam button starts warming up. The steam lamp is blinking until the warm up process is completed.
It takes approximately 1 minute 30 seconds to complete the warm up process. 
The steam lamp is on and normal steam is discharged once the warm up process is completed.
-Strong/Medium/Weak is cycled when pushing the steam button.
  Strong: Steam 60% Water Drop 40%
  Medium: Steam 70% Water Drop 30%
  Weak: Steam 80% Water Drop 20%
Once steam is sprayed, start cleaning process.
To remove stubborn stain, add a cleaning brush to the front of the nozzle.
※ Do not use the equipment more than 15 minutes at a time 

 the machine may stop because of heater overheated.

※ Steam coming from the device is very hot and may cause burn. Do not spray to people or animals
※ The nozzle spraying steam is very hot and may cause burn

[Lack of Water]
When there is no water in the inner water tank or lack of water coming from the water induction hose, 
alarm sounds and the machine stops. 
At this time, the steam lamp starts blinking. The steam button does not work until the heater is cooled.
If you hear alarm sound, supply water for the inner water tank or the water induction hose. 
Then, press the cooling/stop button to cool the heater until the lamp stops blinking by discharging water. 
When the steam lamp stops blinking after heat is cooled, continue cleaning by pressing the steam button 
(strong/medium/weak).
※ No idling for a long time when there is no water. It is dangerous due to rapid overheat of the heater.
 
[Completion of Work]
When cleaning is completed, press the cooling/stop button to stop the machine.
Press the cooling/stop button again to cool the machine for 20-30 seconds by discharging water. 
Press the cooling/stop button to stop the cooling.
Remove water from the machine by opening drain cap at the bottom of machine, and unplug the power cable.
 
[Maintenance]
Strange materials can be generated inside the machine if it is used for a long time. 
Clean compounds and strange materials when amount of steam is significantly reduced or pressure is decreased. 
Amount of steam can be restored to the original steam amount and the life of the machine can be extended after 
removing such compounds and strange materials.
 
※How to remove strange materials from the inside (for complete cleaning, water induction method is recommended)
1. Make sure that the power cable is unplugged and power switch is off.
2. Add water to water tank and mix 10 spoons of citric acid.
3. Supply power and pressing the cooling/stop button to induce and discharge the citric acid mixture for more than 
   15minutes.
4. Turn the power of the main body off by pressing the cooling/stop button and discharge the citric acid mixture 
    from the inside by opening drain cap at the bottom of machine
5. Repeat above procedure with cool water instead of citric acid mixture three times to completely remove strange 
    materials from the inside.

Summary of Contents for CROD

Page 1: ... than 15 minutes at a time Do not share power source with other equipment e g connect it to a power strip Export Department nd Provenza 392 2 floor 08025 Barcelona Phone 34 93 446 27 81 Fax 34 93 446 27 96 export salvadorescoda com ...

Page 2: ...ure that electric wires and cords are disconnected with wall sockets before starting cleaning or maintenance after completing use of the device Features of Product Product Specification Spraying high pressure temperature steam Environment friendly cleaning without chemicals use and sterilization effect with high temperature cleaning As it uses an instant heating method without a hot water generato...

Page 3: ...upplying water Open the top cover by rotating it 90 degree anti clockwise Supply approx 4ℓof clean water slowly to prevent overflow and close the cover Power Connection Connect the power cable of the main body to a rated power source check if the LED on the front display is on Make sure that only the rated power is used Do not share power source with other equipment Water Tank Cover Handle Control...

Page 4: ...p stops blinking by discharging water When the steam lamp stops blinking after heat is cooled continue cleaning by pressing the steam button strong medium weak No idling for a long time when there is no water It is dangerous due to rapid overheat of the heater Completion of Work When cleaning is completed press the cooling stop button to stop the machine Press the cooling stop button again to cool...

Reviews: