Salamander Pumps Right Pump Series Installation And Warranty Manual Download Page 25

25

To the installer

Please follow the guidelines for installation 

provided in this brochure and call the 

PumpWise helpline for installation advice. 

Once installation has been completed and the 

system has been tested to your satisfaction, 

please assist the customer in Warranty 

registration online at www.salamanderpumps. 

co.uk or by phone on 0191 516 2002

Terms, conditions and 

warranty

1. The Scope of the Warranty
SALAMANDER PUMPED SHOWER SYSTEMS 

LTD (“the company”) Warrants subject to the 

terms and conditions below for the Warranty 

period(s) specified in paragraph 3 that the 

Company shall:
Repair or replace free of charge the product(s) 

specified on the Online warranty form or 

any component part thereof (together 

referred to as “the equipment”) which shall 

in the opinion of the Company have proved 

defective by reason only of the Company’s 

materials or workmanship providing always 

that the Company shall be under no obligation 

whatsoever under this Warranty to repair or 

replace equipment which have been misused, 

tampered with, modified/altered in any way 

without the consent in writing of the Company 

or if any component or accessory shall have 

been replaced by a type not specified by the 

Company or if the equipment is incorrectly 

installed or operated or used other than as 

described in the instruction manual or if any 

servicing or repair of the equipment shall 

have been carried out otherwise than by an 

authorised Company dealer appointed by the 

Company (“dealer”).
The Company’s liability under this Warranty 

is limited to the said repairs or replacement 

and shall under no circumstances extend 

to any financial loss or damage including 

consequential losses alleged to have been 

suffered by the claimant.

Subject as provided in this warranty and 

except where the equipment is sold to a 

person dealing as a consumer all warranties, 

conditions or other terms implied by law are 

excluded to the fullest extent permitted by 

law.
Nothing in this warranty shall exclude liability 

for death or personal injury caused by the 

Company’s negligence
2. Terms and conditions
This Warranty shall only be enforceable by 

you if the following terms and conditions have 

been complied with:
a. That the pump has been installed in 

accordance with the installation instructions, 

guidance and advice contained within the 

installation and warranty guide and/or 

provided by the Salamander help desk.
 b. You are the original purchaser of the 

equipment from a dealer and not an assignee 

or subsequent purchaser of the equipment.
c. You must evidence the date of purchase by 

retaining the original invoice from the dealer. 

Without such evidence the Company reserves 

the right to reject any such claims under the 

terms of this Warranty.
d. Within 15 days of delivery of the equipment 

to you the Warranty is accurately completed 

online or by phone.
e. Within 30 days of discovery of a defect 

giving rise to liability under paragraph 1 

above you give notice thereof in writing to the 

Company.
f. Provided the pump has not been altered, 

tampered with, modified or transformed in any 

way.
3. The Warranty periods
The Warranty periods referred to in paragraph 

1 above are as follows:
a. Products manufactured by the Company 

3 years from date of purchase provided the 

warranty is completed online or by phone 

within 15 days of purchase.

Summary of Contents for Right Pump Series





























Reviews: