Salamander Pumps CT FORCE 15 PT Installation And Warranty Manual Download Page 15

13

Installation

Specifications

Trouble shooting

PumpWise

Warranty

Salamander PumpWise

Salamander PumpWise is your guarantee to:
•  help you select the right pump for the job.
•  avoid installation pitfalls.
•   provide a further TWO YEARS  

WARRANTY FREE (UK only)

All you have to do is to implement the 
technical advice recommendations for any 
specific installation and register the pump 
when installation is complete.

PumpWise helpline 0191 516 2002

PumpWise from Salamander helps customers 
and provides a support service second to 
none. Installers and customers can be sure of 
a speedy response to requests for technical 
help guidance and advice.

Pump noise

Salamander has engineered this product 
range to be as quiet as possible, however no 
pump is completely silent. Correct installation 
(anti-vibration couplers straight, rubber feet 
fitted) will minimise noise, vibration and 
transmission noise.

Standards and approvals

Splash proof rating IPX2; complies with the 
requirements of current British and European 
safety standards for household and similar 
electrical appliances; meets with Compliance 
with European Community Directives (CE). 
Due to continuous improvement and  
updating specifications may be altered 
without prior notice.

Safety in operation

These appliances are not intended for use 
by persons (including children) with reduced 
physical, sensory or mental capabilities, 
or lack of experience and knowledge, 
unless they have been given supervision or 
instruction concerning use of the appliance 
by a person responsible for their safety. 
Children should be supervised to ensure that 
they do not play with the appliance.

Summary of Contents for CT FORCE 15 PT





















Reviews: