background image

 Page 1 

SAFETY / QUICK TIPS

When using this machine, safety precautions should always be followed including:

 IMPORTANT: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

 Never leave machine unattended, especially around children.

 Never leave on overnight or when no one is close to machine. This includes both heat and/

or motor.

 Machine should be cleaned and inspected daily. This includes electrical switches, 

thermostat and general operation.

 Do not operate the machine if you observe any damage. If the machine has any damage

whatsoever, it must be returned to Sagra Inc. for examination or repair immediately.

 When the bowl is removed, the base can be extremely hot. Avoid any contact with the top

of the base as the heating element is located directly beneath and you could be burnt.

 Avoid any other surfaces that have become hot during use.

 Always unplug the machine from the electrical outlet when it is not in use, especially 

before putting on parts, taking off parts and before cleaning.

 To protect against electrical shock and damage to the machine, do not put the base in 

water, dishwasher or a sink. Never allow liquid to enter the base through the bottom grate, 
vent holes, or other openings. Clean the base by hand only.

 When bowl is removed, take caution to keep liquid from entering into the top of the base.

 Avoid contact with all moving parts, such as the spindle.

 Do not allow the power cord to come into contact with hot surfaces. Extension cords are 

not suggested. If an extension cord is needed, verify first with a qualified electrician. Care 
should be taken to position the electrical cord so that it does not create a hazard by hanging 
over a table or counter edge in such a way where it might be tripped on or pulled by those 
around the machine.

 Never place any object, especially your fingers, inside the bowl while the machine is on.

Doing so may cause severe injury and/or damage to the machine itself.

 The use of accessory attachments, other than those made available specifically for use with 

this machine, is not recommended by the manufacturer and may cause injury and will void 
your warranty.

 Extreme caution must be used when moving this machine or it's components containing 

hot liquid. Always move by lifting the base. Do not lift by the bowl.

 Do not use this machine for other than its intended use.

 The machine must be on a level surface to operate properly. 

 Observe and follow customary sanitation guidelines when using this machine.

Summary of Contents for DCD-150











Reviews: