Safran MorphoAccess SIGMA Extreme FFD iCLASS Installation Manual Download Page 4

Page: 4 / 79

MorphoAccess® SIGMA Extreme Series - Installation Guide

Identity & Security

Table of Content

This document and the information therein are the property of

Safran Identity & Security

They must not be copied or communicated to a third party without the prior written authorization of Safran

2017_2000024418 - V1

April 2017

Table of Content

Warning ........................................................................................................................................ 2

Revision History ............................................................................................................................ 3

Section 1 : Introduction ................................................................................................................ 9

MorphoAccess® SIGMA Extreme Series Terminal ................................................................... 10

Scope of the document ............................................................................................................ 11

Safety Instructions ................................................................................................................... 12

Wiring Recommendations ................................................................................................... 13

Regulatory, safety and Environmental notices ....................................................................... 14

European Union (CE) regulatory notices ............................................................................. 14

USA (FCC) regulatory notices ............................................................................................... 15

Canada (IC) regulatory notices ............................................................................................ 16

Others recommendations .................................................................................................... 17

Recommendations for terminal implementation .................................................................... 18

Section 2 : General Description .................................................................................................. 21

Box opening ............................................................................................................................. 22

Components of the initial package ......................................................................................... 23

Terminal's front view description ............................................................................................ 24

Terminal's rear view description ............................................................................................. 25

MorphoAccess® SIGMA Extreme Series Technical Characteristics ......................................... 26

Section 3 : Installation Procedure ............................................................................................... 28

Before proceeding to the installation ..................................................................................... 29

Installation .............................................................................................................................. 30

Required tools (not supplied)............................................................................................... 30

Equipment from the initial package to use ......................................................................... 30

Step by step procedure ........................................................................................................ 31

Section 4 : Electrical Interface .................................................................................................... 35

Wiring overview ...................................................................................................................... 36

Power Supply ........................................................................................................................... 37

External Power supply ......................................................................................................... 37

POE (Power Over Ethernet) ................................................................................................. 37

Output Relay ........................................................................................................................... 38

Nominal characteristics of relay .......................................................................................... 38

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS














































































Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands

Safran MorphoAccess SIGMA Extreme FFD iCLASS, Installation Manual

Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands