Safran MorphoAccess SIGMA Extreme FFD iCLASS Installation Manual Download Page 30

Page: 30 / 79

MorphoAccess® SIGMA Extreme Series - Installation Guide

Identity & Security

Section 3 :Installation Procedure

This document and the information therein are the property of

Safran Identity & Security

They must not be copied or communicated to a third party without the prior written authorization of Safran

2017_2000024418 - V1

April 2017

Installation

Required tools (not supplied)



Six (6) raw plugs + six (6) screws ø4mm max and length adapted to the wall material.



One (1) screwdriver adapted to screws above.



One (1) Drill (with a drill bit diameter adapted to raw plugs above).



One (1) hole saw (depending on installation case).



A (1) Torx T20 screwdriver



Deadbolt/door strike



Snubber diode required to protect regulated DC power supply from inductive

kickback (1N4007 diode or equivalent recommended)



Separate power supply for the deadbolt/door strike based on supplier's

recommendations.



External relay (if required)



Networking cable

For UL-294 compliance, an earthed screen in the wire or around all wires to/from
product is only required when the wires share space/compartment/tube with high
voltage cables.

Equipment from the initial package to use



One (1) Terminal’s body.



One (1) wall plate.

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS














































































Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands

Safran MorphoAccess SIGMA Extreme FFD iCLASS, Installation Manual

Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands