Safran MorphoAccess SIGMA Extreme FFD iCLASS Installation Manual Download Page 38

Page: 38 / 79

MorphoAccess® SIGMA Extreme Series - Installation Guide

Identity & Security

Section 4 :Electrical Interface

This document and the information therein are the property of

Safran Identity & Security

They must not be copied or communicated to a third party without the prior written authorization of Safran

2017_2000024418 - V1

April 2017

Output Relay

Figure 14: Output relay wiring

21 Yellow / White

Relay NO

Contact relay (normally open)

22 Grey / White

Relay COM

Contact relay common

19 Orange / White

Relay NC

Contact relay (normally closed)

Nominal characteristics of relay

Load characteristics:



1 A max @ 30 VDC (according to the safety extra low voltage requirements

independently of the power supply),



Resistive load or inductive load; see warning information hereafter for inductive

load,



The internal relay is designed for at least 100 000 cycles (resistive load).

Inductive load management requires a parallel diode for a better contact
lifetime.

Example of connection for electrical door locks

Figure 15: Example of electric latch connection

+ VCC <30V

Imax < 1A

Electric

door lock

Protection

diode

MorphoAccess®

SIGMA Extreme

Terminal

Button on other

side of the door

Relay

Pin 1

Relay

Pin 2

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS














































































Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands

Safran MorphoAccess SIGMA Extreme FFD iCLASS, Installation Manual

Search results

Summary of Contents for MorphoAccess SIGMA Extreme FFD iCLASS

Reviews:

Brands by name

Popular brands