SafetyLink LADER002.LHD.90 Installation Handbook Download Page 5

Page: 5 / 36

Return to Table of Contents

Ref: SafetyLink Pty Ltd Permanent Ladder System

Page 5 of 36

Doc ID: MKT-471 Version: 19.0

LADDER TECHNICAL SPECIFICATIONS

MATERIALS

All components and accessories of SafetyLink ladder system are manufactured from structural aluminium.

WEIGHT

90-degree 1350mm Ladder head: 6.8kg

75-degree 1350mm Ladder head: 6.8kg

2400mm Ladder section: 7.8kg

1200mm Ladder section: 3.9kg

One set of Splice Joints: 1kg

DIMENSIONS

Ladder width-603mm

Stiles distance inbetween-525mm

Rung spacing-300mm

Stile extension above last rung-1150mm (75-degree Ladder), 1050mm (90-degree ladder)

FIXING TO SUPPORT STRUCTURE (NOT SUPPLIED BY SAFETYLINK)

STRUCTURE

SURFACE FASTENERS

Timber:

3 x 14-gauge Roofing Screws (to penetrate at least 35mm into structure).

Steel:

2 x M10 Bolts fixed through the structure.

Concrete:

2 x M10 Masonry Bolts or equivalent.

Steel Purlin: 3 x M10 Bolts/Toggle Bolts.

SAFE WORKING LOAD

SafetyLink ladder system is designed for single person use and rated for maximum 150kg.

The building or structure for the anchorage should be assessed by an Engineer, unless it is clear to a competent

height safety installer that the structure is adequate.

TESTING

The SafetyLink ladder system has been tested and manufactured in accordance with Australia and New Zealand

Standard AS/NZS 1891:2009 and Australian Standard AS 1657:2018.

Summary of Contents for LADER002.LHD.90





































Search results

Summary of Contents for LADER002.LHD.90

Reviews:

Related manuals for LADER002.LHD.90

Brands by name

Popular brands

SafetyLink LADER002.LHD.90, Installation Handbook

Search results

Summary of Contents for LADER002.LHD.90

Reviews:

Related manuals for LADER002.LHD.90

Brands by name

Popular brands