SAFE HOME WS110-V2, Manual

Page: 3 / 20

www.safehome.dk www.safehome.dk 4
5
2.2. Powering up the WS110 Dialer Plus
a.) Back up power: Unscrew the battery compartment and remove the cover. Insert 4
“AA” Alkaline batteries noting the polarity as shown in the battery compartment.
b.) AC Power Supply: Plug in the AC adaptor to the Dialer Plus and connect it to a wall
socket. LCD will blink within 1 second once powered up. When the power supply
switches from the battery to the AC Adaptor, the [AC symbol] will appear.
Note: 4 “AA” Alkaline batteries serves as backup power when AC power failed, and you
should not rely on battery power and make sure proper AC power is supplied to the
dialer at all times. When batteries run low, the “BATT.” icon flashes until new batteries are
replaced.
2.4. Connect the dialer WS110 to your home telephone
A phone line must be connected to the dialer in order for the dialer to work.
• Open the battery door at the back; there are 2 sockets for telephone cables.
• Connect the “Line” socket to your wall telephone jack.
• Connect the “Phone” socket to your telephone, which then will share the same phone
line with the Dialer plus. Normal telephone functions are interrupted only during emer-
gency, when Dialer plus took control of the phone line.
Section 3 - Programming the Autodialer
3.1 To ENTER the SETUP mode while in the
STANDBY Mode:
• Press “MENU” to activate the keyboard
• Enter the 4 digit PIN code. (Default PIN code is “1234”)
• Press “ENTER/EXIT” to go into SETUP mode
3.2 To RECORD the message you want to play when the
dialer is triggered while in the SETUP Mode
• Make sure you are in the SETUP mode, following the steps in “3.1”
• Press and hold “REC/PLAY” for 2 seconds, until the REC shows up on the screen to
start the recording.
• Press the “REC/PLAY” again after you completed recording, or the recording will stop
automatically when it reached 20 seconds maximum recording time.
3.3 To RECORD an effective message for help
Makes sure the message includes clear descriptive information of your address and / or
your identity (when applicable) for the person you are calling to quickly come to your aid.
The message should also contain the simple instruction to allow the person you are call-
ing to start communicating with you over the Dialer plus.
For example: “This is a security alert from <*your resident or business name >, at
<*your resident or business address >. *After having full listened to this message,
please press the hash key (or pond sign), followed by either “1” to “Listening-in” or “3” to
“Speaking-in” and so forth. Over”
3.4 To PLAYBACK the recorded message:
• Make sure you are in the SETUP mode, following steps in “3.1”
• Press and release the “REC/PLAY” to play back the recorded message
3.5 To CHECK PHONE NUMBERS stored:
• Make sure you are in the SETUP mode, following steps in “3.1”
• Press “MENU” (display will show “1” for 1st phone number), press “MENU”
again for checking the other phone numbers
3.6 To ENTER/STORE PHONE NUMBERS:
• Make sure you are in the SETUP mode, following steps in “3.1”
• Press “MENU” (Display will show “1” for 1st phone number), Repeat this step to
choose which phone numbers you wish to program (1, 2, 3, 4, 5, 6, 7, 8)
• Press “PROGRAM” and enter the phone number digits (Maximum 16 digits)
• Press “CLEAR” to clear a wrong number you entered
• Press “ENTER/EXIT” to complete this step
*) Please note that you should program the numbers in the sequence of importance to
you. Dialer will NOT dial later numbers when an earlier person you wish to call has been
successfully reached.
3.7 To DELETE a stored phone number:
• Make sure you are in the SETUP mode, following steps in “3.1”
• Press “MENU” (Display will show “1” for 1st phone number), Repeat this step to choose
which phone numbers you wish to DELETE (1, 2, 3, 4, 5, 6, 7, 8)
• Press “PROGRAM” and “ENTER/EXIT” to confirm erasing
3.8 To program the number of DIALING CYCLES
• Make sure you are in the SETUP mode, following steps in “3.1”
• Press “MENU” (Display will show “1” for 1st phone number), Repeat this step until the
display shows “CYCLE”
• Press “PROGRAM” and enter the number of cycles you wish (1 through 0, default cycle
is 3 times)